The following components and instructions pertaining to the closure/assembly of specific products you purchase are supplied to you in compliance with (49CFR), Part 178.2 (c)(l)(iii) and Subpart M, section 178.601 (b). You must, by law adhere to these requirements when preparing the package for shipment. You must also provide written notification to each person who whom this package is transferred of the type and dimensions of any closures needed to satisfy UN performance test requirements.

CLOSING PROCEDURES FOR ALL TIGHT HEAD UNITS:

1. PLUG AND CLOSURE THREADS MUST BE DRY.

2. SPECIFIED GASKETS MUST BE INSTALLED ON PLUGS.

3. THREAD PLUGS INTO CLOSURES BY HAND TO START.

4. TORQUE PLUG TO REQUIRED VALUE.

5. INSTALL SEALS WHERE REQUIRED.

The following components and instructions pertaining to the closure/assembly of specific products you purchase are supplied to you in compliance with (49CFR), Part 178.2 (c)(1)(iii) and Subpart M, section 178.601 (b). You must, by law adhere to these requirements when preparing the package for shipment. You must also provide written notification to each person who whom this package is transferred of the type and dimensions of any closures needed to satisfy UN performance test requirements.

OPEN HEAD PLASTIC DRUM CLOSING:

1. PLACE LID W/GASKET AS SUPPLIED ON THE TOP OPENING OF THE DRUM.

2. PLACE SUPPLIED CLAMP BAND AROUND LID.

3. ENSURE CLAMP BAND AND LID ARE ON PROPERLY THEN ENGAGE THE LOCKING MECHANISM OR TORQUE BOLT STYLE UNTIL TIGHT, ENSURING THAT THE CLAMP BAND IS LATCHED OR TORQUE TIGHT.

POLY TIGHT HEAD DRUM  -  DRUM CODE: 55GALLON 1H1

PRODUCT:    55 DELCONDRO 0205 ALL COLORS

UN MARKINGS:   UN/1H1/Y1.9/150/R/USA/+AG0052

PLUG/GASKET/PART#/TORQUE:    (1) 2"SPPI BUTTRESS PLUG W/EPDM GASKET TORQUE TO 250LB5 PART#A55XXX

PLUG/GASKET/PART#/TORQUE:    (1) 2" NPS SPPI PLUG W/EPDM GASKET TOURED TO 250LB5 PART#PPA57

POLY TIGHT HEAD DRUM (CARBOY)  - DRUM CODE: 5 GALLON 3H1

CLOSURE:    RIEKE ES-70.. 70mm SCREW CAP W/ 3/4" THREAD REDUCER

UN MARKINGS:    3H1/Y1.8/100/98 USA/+AA0762

CLOSURE DIMENSIONS:    FS-70 HEIGHT.985" DIAMETER S.280"

CLOSURE GASKET:    EPT RUBBER GASKET

CLOSURE TORQUE:   MINIMUM 120 In-Lbs.

CLOSURE TOOLS:   SEEKONK TORQUE WRENCH(GAUGE) OR EQUIVALENT W/RIEKE CAP WRENCH ADAPTER, W394.

POLY TIGHT HEAD DRUM  -  DRUM CODE: 15 GALLON 1H1

PRODUCT:    15 DELEX 0203 ALL COLORS

UN MARKINGS:     UN/IHI/Y1.8/100/R/USA/+AG0037

PLUG/GASKET/PART#/TORQUE:    (1) 3/4"NPS TRI-SURE PLUG W/EPT GASKET TORQUE TO 60LBS PART#A0211X

PLUG/GASKET/PART#/TORQUE:    (1)  2" NPS SPPI PLUG W/EPDM GASKET TORQUE TO I50LBS PART#A0211X

POLY TIGHT HEAD DRUM  -  DRUM CODE: 30 GALLON lHl

PRODUCT:    30 DELCONDRG 0205 ALL COLORS

UN MARKINGS:    UN/1H1/Y1.8/100/R/USA/+AGOO28

PLUG/GASKET/PART#/TORQUE:    (1) 2" SPPI BUTTRESS PLUG W/EPDM GASKET TORQUE TO 250LB5 PART#A55XXX

PLUG/GASKET/PART#/TORQUE:    (1) 2" NPS SPPI PLUG W/EPDM GASKET TORQUE TO 250LB5 PART#A20XXX

POLY OPEN HEAD DRUM -  DRUM CODE: 55 GAL 1H2

PRODUCT:   55 DELCON 0/H W/5/8" BOLT RING ALL COLORS

UN MARKINGS: UN/1H2/Y250/SYR/USA/M4235

PLUG/GASKET/PART#/TORQUE:    (1) 21 1/2" NATURAL LID W/O BUNGS W./FOAM GASKET

PLUG/GASKET/PART#/TORQUE:    (1) 16 GAUGE BOLT RING W/5/8" BOLT TORQUE UNTIL TIGHT